Local contractor in 21001

A faulty tub and spout can lead to frustrating leaks and water damage. We replaced the damaged tub and installed a new brushed nickel tub spout, ensuring the installation was secure and properly sealed. After re-siliconing the spout to the wall, we confirmed there were no leaks and that the water diverts perfectly.

A malfunctioning toilet fill valve can lead to water wastage and inefficiency. We replaced the old fill valve with a Fluid Master model, ensuring optimal performance. Additionally, we rejuvenated the component isolation control system, followed by thorough performance and safety testing to guarantee reliability and function.

We addressed a broken kitchen sink drain line on the DWV pipe by expertly repairing the damaged section. After the reconnection, we tested the system thoroughly to ensure optimal performance and complete functionality, leaving the sink in excellent working condition.

Supported 11/2” pvc dishwasher discharge adding air gap at floor sink. Supported ice machine and soda dispenser tubes adding air gap in bar area. Disassembled tilt lever strainer drain and put back together using new gasket and commercial grade putty to stop leaks and standing water in prep area.

Leaking angle valves in the vanity prompted us to perform a valve replacement. We replaced both valves with durable 1/4 turn angle valves to stop the leak and enhance reliability. Additionally, we conducted water leak detection service and executed performance and safety testing to ensure the entire plumbing system operates efficiently.

The toilet was experiencing frequent leaks, disrupting daily use. We replaced the defective flapper on the Bristol toilet, ensuring a secure seal and restoring proper functionality. The repair helps prevent water wastage and enhances the overall efficiency of the toilet system.

An excessive buildup caused a significant blockage in the drain. We addressed this issue by snaking the line multiple times, thoroughly clearing the obstruction down to the septic system. After raising the toilet on a plywood riser, we reset it with a new wax ring and bolts to ensure a proper seal. Please note, we do not guarantee drain cleaning results, and are not responsible for any floor damage or recaulking requirements.

Master shower leaking into living room ceiling, this is a custom shower with a rubber membrane under the tile. Removed strainer cover and noticed there was only about 1 inch diameter drain due to tons of hair and debris, after removing all the hair and debris you could literally see the membrane draining back into the drain meaning when it was clogged up, the water was going in between the drain and the membrane. This shouldn’t happen again as long as the drain is kept clear, if it does, there is an issue with the membrane and tile.

In addressing the outdated water line connection for the ice maker, we removed the existing ice maker line and copper components. We installed a new valve and tubing, ensuring a reliable setup. As the fridge is not yet in place, the customer was comfortable with the temporary arrangement of the new line until their appliance arrives.

A short tailpiece was identified as the cause of performance issues. We promptly replaced it with a longer, more suitable tailpiece, ensuring optimal functionality. After installation, we conducted thorough performance and safety testing, confirming that the system meets all operational standards.

Frozen CPVC lines led to a split affecting the kitchen sink. We efficiently capped off the lines as per the customer’s request to prevent further leaks. Additionally, we conducted comprehensive water leak detection and performance testing to ensure safety and functionality.

The ice maker was not functioning properly due to issues with its brass valve. We rebuilt the valve using a rebuild kit, ensuring all components were in optimal condition. After flushing the valve thoroughly to eliminate any debris, we conducted tests to confirm its effective operation.

We encountered a broken sewer line while attempting to snake from a clean-out in the yard. Our efforts allowed us to reach only about 10 feet before the cable became stuck. We pulled back mud, confirming the issue required further action. To resolve the problem, we determined it was necessary to dig up the sewer line at the clean-out and extend a bit further for proper repair.

A severe stoppage in the second floor toilet prompted us to take action. We pulled the toilet and worked for three hours to snake the line, but it appears to be frozen solid. Unfortunately, due to no access to the crawlspace, the line will need time to thaw naturally. We reset the toilet and completed our cleanup.

A frozen sump pump discharge line was hindering the pump's operation. We cut out the obstructed section to restore proper flow, ensuring that the pump could function efficiently once again. This work helped resolve the issue and maintain optimal performance for the customer's system.

A PVC drain line in the crawlspace had separated at the hub due to improper installation. We cleaned both the pipe and fitting, then reassembled them using primer and glue to ensure a secure bond. After completing the repair, we ran water for five minutes to test the connection. If complications arise again, the next step would involve replacing a 3 to 4-foot section between the walls.

A clogged bathtub prompted us to take action, so we snaked the drain 25 feet to effectively clear the blockage. While tackling the issue, we discovered and removed a rag wipe. Additionally, we plunged the sink to eliminate any remaining obstructions, leaving all fixtures functioning properly with no further issues.

A leak was detected under the vanity due to a split in the supply nut. We promptly replaced both hot and cold supply lines to resolve the issue. There are no further concerns with the plumbing now, ensuring reliable performance moving forward.

Install customer supplied 1/2hp jet pump with all new fittings and tubing due to several leaks on system. Also will replace gauge and ball valve.

A clogged tub drain caused frustration, so we promptly removed the hair blockage and expertly cabled the drain. We also performed performance and safety testing to ensure everything was functioning smoothly and securely. Fixture lines were rejuvenated to restore optimal water flow and functionality.

Upon noticing a diagnosis of a low flow toilet and weak flush, we assessed the plumbing system and identified the need for a new toilet installation.

A slow flush issue in the toilet prompted us to investigate underlying causes. We started by cleaning the aerator of debris in the lav faucet and then auger’d the toilet to improve its performance. Additionally, we adjusted the pressure regulator valve (PRV) from 40psi to 55psi. While the PRV is old but functional, we recommend considering its replacement if pressure problems recur.

A leaking evo fitting was identified under the left side of the Master bath vanity, causing concerns about water damage. We replaced the faulty fittings on the cold side, ensuring a secure installation. Additionally, we conducted thorough water leak detection and performed performance and safety testing to guarantee everything was functioning properly.

After the vanity valve was turned off, it blew apart, leading to an urgent need for repairs. We replaced both the hot and cold shut-off valves to ensure the plumbing system was functioning safely and efficiently. This restoration provided the customer with peace of mind and reliable water flow.

A malfunctioning p trap caused water backup issues, prompting us to replace the waste and overflow components. After ensuring proper installation, we conducted thorough performance and safety testing, confirming that the plumbing was operating efficiently and securely.

To ensure optimal performance of the tankless water heater, we conducted a thorough flush using Blue Monster Velocity flush solution. This process lasted 30 minutes, followed by an additional 10 minutes of flushing with fresh potable water. After restoring water to the heater and powering it up, we recommended an annual maintenance procedure to keep the unit running efficiently.

The Kohler shower was dripping from the head and not shutting off completely. We took apart the unit and discovered that both the balance block and cartridge were thoroughly clogged with dirt and debris from the well. After replacing both components, we re-siliconed the necessary areas to ensure optimal functionality.

A leaking Kohler toilet prompted us to replace its worn-out gasket effectively. This vital repair ensures proper sealing and eliminates unnecessary water waste. In addition, we performed a comprehensive rejuvenation of the component isolation control system, followed by rigorous performance and safety testing to guarantee optimal functionality.

The existing garbage disposal was malfunctioning and causing inconvenience in the kitchen. We replaced it with a high-performance In-sink Erator, ensuring a reliable and efficient waste management solution. After installation, we conducted thorough performance and safety testing to guarantee optimal functionality.

A persistent water leak was traced to a faulty hose bib, prompting the need for a solution. We removed the old dripping hose bib and installed a Wolverine Frost Proof model, complete with a shut-off valve for enhanced control. Alongside this, we conducted thorough water leak detection and performance testing to ensure everything functions optimally and safely.